Coo-Var Danish Oil | Tung Oil Wood Finish to Seal, Protect & Enhance Interior & Exterior Wood

• Seal, protect and enhance kitchen worktops, wooden panels or interior joinery with a durable oil finish
• Protect garden furniture, exterior doors and outdoor joinery against moisture and weathering
• Apply a natural, clear slight-gloss finish that enhances the grain of mahogany, teak or most other timbers
• Use a single product for both interior and exterior wood surfaces
• Achieve a fast turnaround — touch dry in 4 hours, recoat the following day

• The surface has not been properly cleaned and prepared — surfaces must be clean, dry and free from wax, oil, grease and dirt; use sandpaper to remove any old coatings or paints before applying
• You require a water-based product — this is a solvent-based oil
• You require a coloured finish — Coo-Var Danish Oil is available in Clear only

Coo-Var Danish Oil is a hard-wearing, water-resistant wood finish formulated with tung oil to enhance, seal and protect interior and exterior wood. Developed by Coo-Var — a British coatings manufacturer with over 115 years of heritage — it penetrates deep into the grain of the wood, nourishing the timber from within and curing to a tough, durable slight-gloss finish that enhances the natural colour and figure of the wood.

The tung oil content gives Coo-Var Danish Oil excellent penetration and durability compared to plain linseed oil-based finishes. It is suitable for mahogany, teak and most other timbers, and is ideal for kitchen worktops, wooden panels, garden furniture, doors and a wide range of interior and exterior woodwork. It provides a good degree of water resistance, protecting the timber against moisture ingress and the effects of outdoor exposure.

Available in Clear in 500ml, it can be applied by brush or lint-free cloth and is touch dry in just 4 hours at 20°C, allowing recoating the following day.

Key Benefits

• Contains tung oil — excellent grain penetration and durability beyond plain linseed oil-based finishes
• Hard-wearing, water-resistant finish — protects timber against moisture ingress and outdoor exposure
• Enhances natural colour and grain — slight-gloss finish brings out the natural beauty of the wood
• Versatile timber compatibility — suitable for mahogany, teak and most other timbers, interior and exterior
• Touch dry in 4 hours — fast drying allows recoating the following day
• Apply by brush or lint-free cloth — simple application, no specialist equipment required
• 115+ years of British expertise — trusted by homeowners, joiners and woodcare professionals across the UK

Order before midday for next-day UK delivery.

Coo-Var Danish Oil is an excellent choice for sealing, protecting and enhancing a wide range of interior and exterior timber surfaces:

• Kitchen Worktops — Apply to hardwood and solid wood kitchen worktops to seal and protect against moisture, staining and daily wear. The tung oil formula penetrates deep into the grain, providing a durable, water-resistant finish that enhances the natural colour of the wood.

• Garden Furniture & Outdoor Joinery — Apply to teak, mahogany and other hardwood garden furniture, benches and outdoor joinery to protect against moisture and weathering. The water-resistant finish helps maintain the natural appearance of the wood through outdoor exposure.

• Interior & Exterior Doors — Apply to hardwood interior and exterior doors to seal and protect the timber and enhance the natural grain. The slight-gloss finish provides a smart, professional appearance suitable for both traditional and contemporary settings.

• Wooden Panels & Feature Walls — Apply to wooden wall panels, feature walls and interior joinery to enhance the natural grain and provide a durable, water-resistant finish. Suitable for most interior timber species including mahogany, teak, oak and pine.

• Mahogany & Teak Furniture — Apply to mahogany and teak furniture to restore and enhance the natural colour and grain. The tung oil content provides excellent penetration and a durable finish that protects against moisture and daily use.

• General Interior & Exterior Woodwork — Use on most interior and exterior timber surfaces requiring a clear, protective oil finish. Suitable for decking, garden structures, window frames, skirting boards and a wide range of general woodwork.

If you need personalised advice on surface preparation or application, contact our experts via the live chat for tailored guidance.

Coverage: 14 m² per litre at 35 micron dry film thickness

Coverage per size

• 500ml: Covers approximately 7 m² per coat

Note: Coverage is dependent on the porosity and condition of the wood. Dry, weathered or very porous timber will absorb more oil and reduce coverage. New or freshly sanded wood will also absorb more on the first coat.

Recommended coats

• 2–3 coats are recommended for best results — the first coat seals and nourishes, subsequent coats build the protective finish
• Recoat after a minimum of 12 hours or overnight at 20°C
• Additional maintenance coats can be applied as required

Example calculations

• For a kitchen worktop of 3 m²: a 500ml tin will cover 2 coats
• For a set of garden furniture (approximately 5–8 m²): a 500ml tin will cover 1 coat; 2 x 500ml for 2 coats
• For a set of interior doors (approximately 4 m²): a 500ml tin will cover 1–2 coats

For accurate project planning, we recommend ordering 10–15% extra to account for surface variation and porosity.

Surface Preparation

• Ensure the surface is clean, dry and free from wax, oil, grease and dirt before applying
• Use sandpaper to remove any unwanted old coatings or paints
• For weathered or greyed exterior wood, clean and revive with Lacq Turbogel Wood Reviver Gel before applying Danish Oil
• Allow the surface to dry fully after cleaning before applying

Application

1. Mix the oil well before use
2. Apply by brush or lint-free cloth to the prepared wood surface
3. Apply generously, working the oil well into the grain
4. Allow to penetrate, then wipe off any excess that has not been absorbed
5. Allow to dry — touch dry in 4 hours, recoat after a minimum of 12 hours or overnight
6. Apply 2–3 coats for best results, following the same method for each coat
7. If thinning is required, thin with Thinners 14 at a maximum of 5%
8. Clean brushes and cloths immediately after use with Thinners 14

Drying Times (at 20°C)

• Touch dry: 4 hours
• Hard dry: 8 hours
• Full hardness: 5–7 days
• Recoat interval: 12 hours or overnight

Drying times will be longer in cold or humid conditions.

Important Notes

• Apply direct to prepared wood — no separate primer required
• Thin with Thinners 14 at a maximum of 5% if required
• Clean equipment with Thinners 14 immediately after use — do not use water

Recommended System Products

Free delivery on orders over £75 — stock up on everything you need in one go and complete the job properly.

Lacq Turbogel Wood Reviver Gel: Clean and revive greyed or weathered exterior wood before applying Danish Oil. Removes grey weathering, dirt and surface contamination to restore the natural wood surface.

Paint Brushes & Paint Trays: Use suitable brushes or lint-free cloths for application. Clean with Thinners 14 immediately after use.

These products are commonly combined for best long-term results.

What is Coo-Var Danish Oil used for?
It is used to seal, protect and enhance interior and exterior wood. It is ideal for kitchen worktops, wooden panels, garden furniture, doors and most other timber surfaces including mahogany, teak and other hardwoods.

Does it contain tung oil?
Yes. Coo-Var Danish Oil contains tung oil, which provides excellent grain penetration and durability.

What surfaces can it be used on?
Mahogany, teak and most other timbers — suitable for kitchen worktops, wooden panels, garden furniture, doors and a wide range of interior and exterior woodwork.

What colour is it?
Clear — it provides a natural slight-gloss finish that enhances the colour and grain of the wood.

What pack size is available?
500ml.

How much does it cover?
Coverage is approximately 14 m² per litre (7 m² per 500ml tin) at 35 micron dry film thickness. Coverage will be lower on porous or weathered timber.

How many coats do I need?
Two to three coats are recommended for best results. Recoat after a minimum of 12 hours or overnight.

How long does it take to dry?
Touch dry in 4 hours at 20°C. Hard dry in 8 hours. Full hardness is achieved in 5–7 days. Drying times will be longer in cold or humid conditions.

Can I thin it?
Yes. Thin with Thinners 14 at a maximum of 5%. Clean equipment after use with Thinners 14.

What do I clean my brushes with?
Clean brushes and cloths immediately after use with Thinners 14. Do not use water — this is a solvent-based product.

Is it flammable?
Yes. This product has a flash point above 32°C and a VOC content of 433 g/litre. Keep away from heat, sparks and naked flames during application and drying. Ensure adequate ventilation at all times.

How do I prepare the surface?
Ensure the surface is clean, dry and free from wax, oil, grease and dirt. Use sandpaper to remove any old coatings or paints. For weathered or greyed exterior wood, clean with Lacq Turbogel Wood Reviver Gel before applying.

Do you offer next-day delivery?
Yes. Order before midday for next-day delivery to mainland UK addresses. Contact us for delivery options to Scottish Highlands, Northern Ireland and other remote areas.

Safety data sheet
Technical data sheet

We recommend these system products to achieve the best results with Coo-Var Danish Oil. Free delivery on orders over £75

Lacq Turbogel Wood Reviver Gel — clean and revive greyed or weathered exterior wood before applying Danish Oil; removes grey weathering, dirt and surface contamination

Paint Brushes & Paint Trays — use suitable brushes or lint-free cloths for application; clean with Thinners 14 immediately after use

Not sure how to prepare your timber or how many coats you need? Contact our experts via live chat for free, tailored advice — we will help you get the best result from your Danish Oil.

Fast, Reliable & Fully Tracked UK Delivery

Every order is dispatched from our warehouse using a fully tracked DX or FedEx service, so you always know when your paint will arrive.

Delivery Options

• FREE Standard Delivery (orders over £75) Arrives in 2–3 working days
• Standard Delivery – £7.95 Arrives in 2–3 working days
• Express Delivery – £13.95 Next working day delivery when you order before 12:00 noon (Mon–Thu)
• Spending £75+? Select Express Upgrade at checkout and only pay the difference

Dispatch & Delivery Times (What Happens After You Order)

• Express delivery (order before 12:00 Mon–Thu) Dispatched same day, delivered next working day
• Standard delivery (Mon–Wed orders) Dispatched next working day, delivered 2–3 working days later
• Orders placed Thursday (standard delivery) Dispatched Friday for Monday delivery
• We do not dispatch or deliver on weekends or UK bank holidays

What to Expect on Delivery

Please provide a contact telephone number at checkout. This allows the courier to share tracking updates or contact you if there are any delivery issues.

Most orders require a signature on delivery. If you may not be available during the day, we recommend delivery to a workplace, business address, or another location where someone can sign.

Outside the UK Mainland?

Delivery prices shown apply to UK Mainland only.

For the Highlands, Islands, Northern Ireland, or non-mainland addresses, please contact us for a quick personalised quote via live chat, by calling 01482 222 421, or emailing info@specialistpaintsonline.co.uk.

Bottom Line

Order today, get fast and reliable delivery, track every step, and get painting without delays.